Bumper Covers & Bumper Parts in Dallas, TX
Bumper cracked, sagging, or hanging off one clip?
Call now (469) 779-0799Send a VIN
Written price back the same business day. Will-call is free, delivery goes out on the morning route.
Bumper Covers & Bumper Parts in Dallas start at $118 at our counter, and the full range is published in the table below. A bumper cover is the painted plastic fascia that clips and bolts over the vehicle's energy absorber and reinforcement bar. A new cover, absorber and reinforcement bar puts the front of the car back where it belongs, usually for a fraction of the dealer quote.
What we keep on the shelf
- front bumper covers
- rear bumper covers
- energy absorbers
- reinforcement bars
- bumper brackets and retainers
- tow hook covers
- park sensor rings
- fog light bezels
- lower valance panels
- bumper mesh grilles
Terms you will hear at this counter and on the phone: CAPA, Certified Automotive Parts Association, TPO plastic, Texas Department of Insurance, Certifit. If any of that is unfamiliar, ask, because getting the vocabulary right is half of ordering the correct part.
Six things worth knowing before you order
- Every bumper cover on the rack gets the same three checks before it leaves: sensor hole spacing, fog light cutout shape, and whether the tab pattern along the fender edge actually lines up.
- Absorbers get forgotten constantly. A cover bolted onto a crushed foam absorber sits proud at the top edge and no amount of clip work will pull it flat.
- Reinforcement bars are where the cheap kits fall down. If the bar is bent even slightly the cover will never sit square, so we sell them as a set when the impact went past the plastic.
- Painted covers ship in a box with a fitted foam collar. Unbox it flat and check the color against the door jamb tag before anyone puts a wrench on the car.
- TPO plastic on a modern cover takes flex adhesive and plastic weld, not body filler. Filler cracks out of a bumper within a Texas summer.
- Sensor-equipped covers need the mounting rings transferred or bought new. A sensor sitting a few millimeters proud throws false parking alerts all day long.
- Tow hook covers and licence plate brackets are sold separately on most applications, and they are the two small parts people discover missing after the cover is already painted.
- A cover with a radar cutout has to be the radar version. The plain version will bolt on and the adaptive cruise will report a blocked sensor from the first mile.
- Upper and lower grille inserts clip into the cover rather than into the header panel on most modern applications, so a cracked insert does not mean a new cover.
- Flex additive goes into the clear on a bumper cover for a reason. Without it the clear cracks along the flex lines within a couple of Texas summers.
- Rear covers with exhaust cutouts vary by trim level, and a dual-exit cover on a single-exit car is the most common wrong-part return in this category.
- The centre lower section of a front cover is frequently a separate valance panel, and replacing just that is a thirty dollar repair instead of a two hundred dollar one.
Prices published · CAPA options stocked · Same-day will-call
Give us the VIN and we pull the right interchange rather than guessing from a model name.
Bumper Covers & Bumper Parts prices in Dallas
| Vehicle class | Aftermarket cover | CAPA certified | Typical OEM part |
|---|---|---|---|
| Compact sedan (Corolla, Elantra, Sentra) | $118 to $175 | $165 to $240 | $420 to $760 |
| Midsize sedan (Camry, Altima, Sonata) | $140 to $210 | $195 to $285 | $480 to $900 |
| Compact SUV (RAV4, CR-V, Rogue) | $165 to $245 | $225 to $330 | $560 to $1,100 |
| Half-ton pickup (F-150, Silverado, Ram) | $190 to $340 | $260 to $430 | $690 to $1,400 |
| Sensor-equipped luxury (3 Series, ES 350) | $260 to $480 | $340 to $620 | $980 to $2,100 |
What pushes a cover to the top of the range: park sensors, a washer jet, adaptive cruise radar behind the grille, and any factory two-tone or pearl finish that has to be matched by a painter rather than shot in one coat.
Does an aftermarket bumper cover void my car's warranty?
An aftermarket bumper cover does not void a vehicle's factory warranty under the Magnuson-Moss Warranty Act. A manufacturer has to prove the aftermarket part actually caused the failure it is refusing to cover, and a painted plastic fascia almost never does.
Can my insurer force me to use a specific bumper cover?
No. Texas Insurance Code Section 1952.301 bars an insurer from limiting coverage by specifying the brand, type, kind, age, vendor, supplier or condition of the parts used to repair your vehicle.
How much cheaper is an aftermarket bumper cover than the dealer part?
An aftermarket bumper cover typically runs 40 to 60 percent below the equivalent OEM part, with unpainted covers for common sedans starting near $118 and dealer covers for the same cars commonly landing between $400 and $1,500.
Before an adjuster tells you otherwise
Texas Insurance Code Section 1952.301 prohibits an insurer from limiting your coverage by specifying the brand, type, kind, age, vendor, supplier or condition of the parts used to repair your vehicle, and Section 1952.302 prohibits an adjuster from telling you that you must use a shop from a preferred list. The statute is public and it is short. Read the whole subchapter here, or read the section numbers back to whoever is on the phone. Working on the same corner of the car? See Fenders & Quarter Panels in Dallas. Working on the same corner of the car? See Pre-Painted Body Parts in Dallas.
Bumper Covers & Bumper Parts questions we get asked
What is the difference between a bumper cover and a bumper?
The bumper cover is the painted plastic skin; the bumper is the steel or aluminum reinforcement bar bolted to the frame rails behind it. A parking-lot tap usually damages only the cover.
Will a CAPA certified bumper cover fit better than a plain aftermarket one?
CAPA certified covers are tested against the car company part for material, fit and finish, and CAPA's own testing found six of seven non-certified metal body parts failed to match OEM yield and tensile strength.
Do I need the bumper absorber and brackets too?
Order the absorber and brackets whenever the impact pushed the cover in far enough to touch them. A reused cracked absorber is the single most common reason a fresh cover sits crooked.
Bumper Covers & Bumper Parts delivered across the Dallas area
Same counter price in every one of these towns, and delivery is not a line item. Each town has its own page with the local detail and the delivery times on it.
- Auto car parts in Farmers Branch
- Carrollton parts delivery
- Car body parts in Plano
- Richardson collision parts
- Auto car parts in Garland
- Rowlett parts delivery
- Car body parts in Mesquite
- Duncanville collision parts
- Auto car parts in Cedar Hill
- Grand Prairie parts delivery
- Car body parts in Arlington
- Irving collision parts
Price this part for me
VIN, or year make and model, plus what broke. That is all we need to quote it.